Questions About Electrical Work
Answers about electrical work in Akron’s older homes, from the first phone call to the final inspection.
- Getting Started
- Safety and Warning Signs
- Panels and Breakers
- Outlets and Wiring
- Lighting
- What Affects Cost
- Permits and Inspections
Getting Started
A job starts with a phone call or a request through Book an Estimate, and a little preparation makes the first visit more useful.
Does someone need to be home during the visit?
In general, yes. The visit means getting into the rooms involved, the basement and the panel, and it ends with an explanation of what was found and what the repair will involve, which is easiest to follow on the spot. If the person who knows the house best cannot be there, a written note of what has been happening helps.
How do I describe an electrical problem over the phone?
In your own words; no technical terms are needed. Say what stopped working, any smell, heat, buzzing or scorch mark, whether it comes and goes or is getting worse, and whether the house has fuses or breakers. For an unfamiliar term on an old report, the electrical glossary puts it in plain words.
Should the problem be left as it is until the visit?
If nothing is hot, smoking, buzzing or sparking, usually yes. A fault that is still showing is easier to trace than one worked around with extension cords and swapped bulbs. If something is hot or smells of burning, switch off that circuit at the panel if you can reach it safely, and call.
Safety and Warning Signs
Heat, smell, sound and small shocks are the usual warnings, and a seasonal maintenance routine catches some problems before they show.
Why does an outlet spark when something is plugged in?
A small, brief spark inside the slots as a plug goes in or out, especially with the appliance switched on, is common and usually harmless. A large or loud spark, a spark with nothing switched on, or a black mark left on the outlet or the plug is not: stop using that outlet, since worn contacts or a loose connection behind it can overheat.
Why would a faucet, a tub or an appliance give a small shock?
Metal that people touch should never carry current. A tingle from a faucet, a tub or an appliance’s case can mean a fault in an appliance or a water heater, or a missing or broken bond between the plumbing and the electrical ground. Stop using it, unplug what you safely can, and treat it as urgent.
What should be done after water reaches outlets or the panel?
Stay out of standing water near outlets, cords or the panel, and never switch anything at a wet panel; if the power cannot be shut off from a dry spot, call the utility or an electrician from outside the flooded area. Outlets and breakers that have been under water usually need replacing, since grit and corrosion stay inside. After a heavy thunderstorm, check the basement floor before going down to the panel.
Panels and Breakers
A panel can be anything from a fuse box to a crowded breaker panel with no open spaces, and a breaker that trips again and again usually comes down to one of a few causes.
Where is the main shutoff, and when should it be used?
Usually it is the large breaker at the top of the panel, or the main fuse block in a fuse box; in some houses it sits in a separate box outside near the meter. Find it before it is needed. Use it when something electrical smells of burning and you cannot tell which circuit it is on, if the panel is safe to reach and the floor is dry. With flames or heavy smoke, leave the house and call 911 instead.
Does it matter if the breakers are not labeled?
More than it seems: in an emergency, a correct label means switching off one circuit instead of guessing at several. A panel can be mapped without opening it. Switch the breakers off one at a time, with a helper or a plugged-in lamp, and note what goes dark, shutting down computers by hand first. Anything still running with every breaker off is fed from somewhere else and worth asking about.
What needs to stay clear around the panel?
Codes generally ask for about three feet of open floor in front of a panel, roughly 30 inches wide, from the floor to well over head height. That means no shelves, freezers or stacked boxes in the way, which takes some watching in a basement laundry area where storage creeps toward the wall. Clear space lets anyone reach the main breaker quickly and lets an electrician work safely.
Outlets and Wiring
Too few outlets and wiring that predates grounding often come as a pair, and both are part of repairs and wiring.
Why do plugs fall out of some outlets?
The spring contacts inside an outlet wear with years of use, and a plug that sags or slips out is no longer held firmly. A loose contact runs warmer than a tight one, so a worn outlet is worth replacing rather than living with, and in an older house the open box is a chance to check the wiring behind it.
Is it all right to rely on extension cords and power strips?
For a lamp or a phone charger, a good power strip is fine. As a lasting answer to too few outlets, they cause trouble: cords under rugs wear through, strips plugged into strips overload one outlet, and a heavy appliance can draw more than a light cord can carry. A room that needs cords everywhere needs more outlets, and sometimes a new circuit.
Can more outlets be added to a room in an older house?
Usually, yes. The first question is whether the circuit can carry more, since one circuit in an older house may feed several rooms; if it cannot, the new outlets go on a circuit of their own. Either way, they are grounded, which the two-prong outlets beside them may not be.
Lighting
A lighting question is often about the ceiling and the switches as much as the fixture, and lighting installation includes that groundwork.
Why does a hallway light work from one switch but not the other?
The light is on a pair of three-way switches, which pass power between them on two wires so that either switch can turn it on or off. When one stops working, the cause is usually a worn switch or a loose wire at one of the two, and finding which takes a tester. Stairways and long halls in older houses sometimes have three-way wiring arranged in ways no longer used.
Can a ceiling light be added where there is no switch for it?
Yes. A new switch can usually go by the door, with cable fished through the wall and ceiling to the fixture, so a room that has always relied on a lamp gets a proper ceiling light. Where opening a wall is not practical, a battery-powered wireless switch paired with a smart fixture is another option.
Why do bulbs burn out quickly in one fixture?
A fixture that goes through bulbs is usually running hot or making a poor contact. A bulb of higher wattage than the fixture is rated for, or a standard LED in a closed globe that traps heat, wears out early, and so does one in a worn socket or under a wobbling ceiling fan. A brittle or scorched socket is worth replacing.
What Affects Cost
What a job costs depends on what is behind the walls; for panel work, the factors that drive the cost can be weighed before anyone opens the panel.
Why does an estimate need a visit?
Because most of what decides the work cannot be seen over the phone: how the house was wired and rewired over the years, what the panel can still take, how a cable can reach the room, and whether the problem is where it seems to be. A description narrows it down; testing at the house settles it.
What makes rewiring an old plaster house take longer?
Mostly the parts nobody can see. Old circuits rarely follow a plan, so each one is traced before it is replaced, and the house usually has to keep working while the new wiring goes in a few circuits at a time. Insulation blown into the walls years later, blocking between floors and furnished rooms all slow the routing of new cable. None of it is unusual in an Akron house built before 1960, but it all adds time.
Why can a small repair turn into a larger one in an older house?
Because the symptom is not always the problem. A scorched outlet can sit on a circuit whose insulation is brittle all the way along, and a tripping breaker can be guarding a circuit asked to carry too much. When testing finds more than the original symptom, each part of the work can be weighed on its own before anything is decided.
Permits and Inspections
Each community sets its own permit rules, though the broad pattern is similar, and panel and service upgrades are among the jobs that usually need one.
Which kinds of electrical work usually need a permit?
In most places, work that adds or changes circuits: a panel replacement or service upgrade, new circuits, rewiring, a generator hookup and EV charger wiring. Swapping an outlet, a switch or a light fixture for a similar one often does not. Each community’s building department sets its own rules and has the final word.
Who arranges the inspection?
In general, whoever holds the permit requests the inspection when the work reaches each stage. Someone then has to let the inspector in to see the panel and the work, which usually means being home for it. If you are not sure who will hold the permit for work on your house, ask before the work starts.
What does an electrical inspector look at?
The work, measured against the electrical code the community has adopted. On a typical job that means the right wire size for each breaker, cables supported and protected where they run, connections made inside boxes with room for them, GFCI and AFCI protection where required, and the grounding at the panel. Larger jobs often have a rough inspection before the walls close and a final one at the end.
When the Answer Depends on Your House
Wiring in an older house seldom matches the general case, and a call is a good place to start with yours.